| Portable Sampler |
| Dual program |
Can run up to two sampling programs sequentially, in parallel, or based on weekly daily worksheets, enabling a single sampler to have multiple sampling capabilities |
| Sampling mode |
"Sampling methods: time weighting, traffic weighting, schedule, traffic table, event triggering |
| Distribution: single mixed samples, multi-bottle mixes, discrete samples, single multi-bottles, single-bottle multi-bottle, or single-type multi-bottle and single-bottle multi-bottle combinations" |
| Running mode |
Continuous or intermittent |
| Status screen |
Displays program operation steps, whether any samples are missing, when the next sample will be sampled, remaining samples, number of recorded channels, last measurement time, available memory, available channels, whether an alarm is triggered, alarm trigger interval, active sensor and cabinet temperature, and so on |
| Alarm |
Alarm information is displayed on the status screen and can also be recorded in the diagnostic alarm log. Alarms can be set for system diagnostic alarms and recording alarms, such as program completion, sampling termination, sampling omission, or full bottle capacity. Channel alarms are alarms for recorded measured values (channels), such as pH value, liquid level, and power supply voltage |
| Manual sampling |
Start sampling independently of the ongoing sampling program |
| Automatically shuts down |
" Multi-bottle mode: After the arm is fully rotated (except for selecting continuous mode). |
| Mixing mode: After all preset samples have been transferred to the mixing container, the sample count ranges from 1 to 999, or a full bottle." |
| Sample volume |
Can be programmed in increments of 10 milliliters (0.34 ounces), ranging from 10 to 10,000 milliliters (3.38 ounces to 2.6 gallons). |
| sampling interval |
"You can choose a single increment from 1~9,999 flow pulses (instantaneous contact closure for about 25 milliseconds or 5~12V DC pulses; Optional 4-20mAh interface), or about 1 to 9999 minutes, with increments of about 1 minute |
| Set point sampling trigger |
If a flow sensor, pH/temperature sensor, or other external detection device is installed, sampling will be triggered after exceeding the set limit range |
| data record |
"Sample history: can store up to 4,000 various data entries, including sample timestamps, bottle numbers, and sample status (completed, bottle full, flushing error, user abortion, dispensing arm error, pump failure, purge failure, sampling timeout, power failure, and low main battery power). |
| Measurement: Up to 325,000 selected measurement channel data can be stored, with data stored at preset recording intervals |
| Event Log: can store up to 2,000 records. It can record various types of data, including power start, power failure, firmware update, pump failure, distribution arm error, low memory battery capacity, low main battery power, user opening, user shutdown, program start, program recovery, program pause, program completed, sample picking, changes in tube requirements, sensor communication errors, cooling failures, heating failures, thermal error corrections, and more." |
| diagnosis |
can view event and alarm logs, as well as maintenance diagnostics |
| refrigerated sampler |
| dual program |
can run up to two sampling programs sequentially, in parallel, or based on weekly daily worksheets, enabling a single sampler to have multiple sampling capabilities |
| sampling mode |
" Sampling method: time weighting, traffic weighting, schedule, traffic table, event trigger |
| Distribution: single mixed samples, multi-bottle mixes, discrete samples, single multi-bottles, single-bottle multi-bottle, or single-type multi-bottle and single-bottle multi-bottle combinations" |
| Running mode |
continuous or intermittent |
| status screen |
" displays program operation steps, whether any samples are missing, when the next sample will be sampled, remaining samples, number of recorded channels, last measurement time, available memory, available channels, whether an alarm is triggered, alarm trigger interval, active sensor and cabinet temperature, etc. |
| alarm |
" alarm information is displayed on the status screen and can be simultaneously recorded in the diagnostic alarm log. Alarms can be set for system diagnostic alarms and recording alarms, such as program completion, sampling termination, sampling omission, or full bottle capacity. Channel alarms are alarms for recorded measured values (channels), such as pH value, liquid level, and power supply voltage |
| manual sampling |
start sampling independently of the ongoing sampling program |
| automatically shuts down |
" Multi-bottle mode: After the arm is fully rotated (except for selecting continuous mode). |
| Mixing mode: After all preset samples have been transferred to the mixing container, the sample count ranges from 1 to 999, or a full bottle." |
| sample volume |
can be programmed in increments of 10 milliliters (0.34 ounces), ranging from 10 to 10,000 milliliters (3.38 ounces to 2.6 gallons). |
| sampling interval |
"You can choose a single increment from 1~9,999 flow pulses (instantaneous contact closure for about 25 milliseconds or 5~12V DC pulses; Optional 4-20mAh interface), or about 1 to 9999 minutes, with increments of about 1 minute |
| Set point sampling trigger |
If a flow sensor, pH/temperature sensor, or other external detection device is installed, sampling will be triggered after exceeding the set limit range |
| data record |
"Sample history: can store up to 4,000 various data entries, including sample timestamps, bottle numbers, and sample status (completed, bottle full, flushing error, user abortion, dispensing arm error, pump failure, purge failure, sampling timeout, power failure, and low main battery power). |
| Measurement: Up to 325,000 selected measurement channel data can be stored, with data stored at preset recording intervals |
| Event Log: can store up to 2,000 records. It can record various types of data, including power start, power failure, firmware update, pump failure, distribution arm error, low memory battery capacity, low main battery power, user opening, user shutdown, program start, program recovery, program pause, program completed, sample picking, changes in tube requirements, sensor communication errors, cooling failures, heating failures, thermal error corrections, and more." |
| diagnosis |
can view event and alarm logs, as well as maintenance diagnostics |
| all-weather sampler |
| dual program |
can run up to two sampling programs sequentially, in parallel, or based on weekly daily worksheets, enabling a single sampler to have multiple sampling capabilities |
| sampling mode |
" Sampling method: time weighting, traffic weighting, schedule, traffic table, event trigger |
| Distribution: single mixed samples, multi-bottle mixes, discrete samples, single multi-bottles, single-bottle multi-bottle, or single-type multi-bottle and single-bottle multi-bottle combinations" |
| Running mode |
continuous or intermittent |
| status screen |
" displays program operation steps, whether any samples are missing, when the next sample will be sampled, remaining samples, number of recorded channels, last measurement time, available memory, available channels, whether an alarm is triggered, alarm trigger interval, active sensor and cabinet temperature, etc. |
| alarm |
" alarm information is displayed on the status screen and can be simultaneously recorded in the diagnostic alarm log. Alarms can be set for system diagnostic alarms and recording alarms, such as program completion, sampling termination, sampling omission, or full bottle capacity. Channel alarms are alarms for recorded measured values (channels), such as pH value, liquid level, and power supply voltage |
| manual sampling |
start sampling independently of the ongoing sampling program |
| automatically shuts down |
" Multi-bottle mode: After the arm is fully rotated (except for selecting continuous mode). |
| Mixing mode: After all preset samples have been transferred to the mixing container, the sample count ranges from 1 to 999, or a full bottle." |
| sample volume |
can be programmed in increments of 10 milliliters (0.34 ounces), ranging from 10 to 10,000 milliliters (3.38 ounces to 2.6 gallons). |
| sampling interval |
"You can choose a single increment from 1~9,999 flow pulses (instantaneous contact closure for about 25 milliseconds or 5~12V DC pulses; Optional 4-20mAh interface), or about 1 to 9999 minutes, with increments of about 1 minute |
| Set point sampling trigger |
If a flow sensor, pH/temperature sensor, or other external detection device is installed, sampling will be triggered after exceeding the set limit range |
| data record |
"Sample history: can store up to 4,000 various data entries, including sample timestamps, bottle numbers, and sample status (completed, bottle full, flushing error, user abortion, dispensing arm error, pump failure, purge failure, sampling timeout, power failure, and low main battery power). |
| Measurement: Up to 325,000 selected measurement channel data can be stored, with data stored at preset recording intervals |
| Event Log: can store up to 2,000 records. It can record various types of data, including power start, power failure, firmware update, pump failure, distribution arm error, low memory battery capacity, low main battery power, user opening, user shutdown, program start, program recovery, program pause, program completed, sample picking, changes in tube requirements, sensor communication errors, cooling failures, heating failures, thermal error corrections, and more." |
| diagnosis |
can view event and alarm logs, as well as maintenance diagnostics |
